ATS2.0 is designed with highly functional capabilities where the user can interface with most demanding applications. The module can control MCB and GCB contactors as well as compact circuit breakers direct from its ports, where two independent signals are required for switching the breaker on and off.

The module allows the user to start the generator for testing or periodical maintenance. While the generator is running, the load can be transferred between mains and generator bus-bars, using the switches on the front panel. If, during this phase, the mains voltage fails, the unit automatically switches to “Auto” mode and connects the load to Generator output.

During operation, mains or generator phase voltages or frequency can both be displayed on the front panel, hence avoiding extra AC voltmeters to be used on the panel. All voltage values are displayed in True RMS values with high reading accuracy.

All unit parameters can be adjusted from the device configuration menu and all program parameter values can be seen on the controller display. The units can also be programmed to control the engine cooldown function, hence allowing simple engine starter units to be used with small capacity generator sets.

KEY FEATURES

• 3 phase Mains voltage and 3 phase Generator voltage measurement
• Switching of MCB and GCB contactors manually with the front panel push buttons
• 3 digit LED display
• 5 configurable I/O ports
• Automatic, Test On-Load and Test Off-Load operation modes
• Full digital calibration of all analog measuring variables
• Plug type terminals on the rear panel
• TrueRMS voltage measurements on both bus-bars
• Load transfer function on Mains frequency monitoring
• Load transfer conditional on Mains phase status (Lock-on Mains bus-bar)
• Remote start and stop operation interface
• Engine cooldown timer for simple Generator controller interface

KEY BENEFITS

• Each phase can be programmed seperately which allows the user to set the system to start the Generator when 1, 2 or 3 phases are out
• Can control pulse type breaker modules directly from its output ports
• The 3 digit LED display is used for voltage readouts and parameter monitoring hence eliminates the need of additional AC voltmeters on the panel
• Engine cooldown function allows simple engine starter units to be used with small capacity Gen-Sets
• Small mechanical outline for minimal control applications
• Full LED indicators on front panel for bus-bar status condition indication
• Configurable I/O ports for customer specific applications

The post ENKO ATS 2.0 appeared first on CSO TRADING.

ATS1.1 is designed with 2 auxiliary outputs and 3 auxiliary inputs. These i/o ports can be configured from the device menu for peripheral device control.

The unit allows the user to crank the generator on for testing or periodical maintenance. This test function can be executed with or without load transfer, allowing testing for the transfer switch at the same time. Normal system operation is maintained in the Automatic mode.

During operation, mains or generator phase voltage can both be monitored on the controller display, hence avoiding extra AC voltmeters to be used on the panel. All voltage values are displayed in True RMS values with high reading accuracy.

All unit parameters can be adjusted from the device configuration menu and all program parameter values can be seen on the controller display. The units can also be programmed to control the engine cooldown function, hence allowing simple engine starter units to be used with small capacity generator sets.

KEY FEATURES

• 3 phase Mains voltage and single phase Generator voltage measurement
• 3 digit LED display
• 5 configurable I/O ports
• Automatic, Test On-Load and Test Off-Load operation modes
• Full digital calibration of all analog measuring variables
• Plug type terminals on the rear panel
• TrueRMS voltage measurements on both bus-bars
• Load transfer function on Mains frequency monitoring
• Load transfer conditional on Mains phase status (Lock-on Mains bus-bar)
• Remote start and stop operation interface
• Engine cooldown timer for simple Generator controller interface

KEY BENEFITS

• The 3 digit LED display is used for voltage readouts and parameter monitoring hence eliminates the need of additional AC voltmeters on the panel
• Engine cooldown function allows simple engine starter units to be used with small capacity Gen-Sets
• Small mechanical outline for minimal control applications
• Full LED indicators on front panel for bus-bar status condition indication
• Configurable I/O ports for customer specific applications

The post ENKO ATS 1.1 appeared first on CSO TRADING.